Ad
Ad
Ad
Pages: [1]   Bottom of Page
Print
Author Topic: Do you leave your printer on or turn it off?  (Read 3673 times)
mr.dude
Jr. Member
**
Offline Offline

Posts: 57


« on: November 27, 2006, 04:14:16 AM »
ReplyReply

If you're not going to be using your printer for a while, do you usually leave it on or turn it off?  

The reason i ask is because i left my IPF5000 unused and off for a mere 12 days and it went through what seemed like a power cleaning cycle when i turned it back on.  it sucked up 20% of the maintenance tank (indicated by the driver) you could hear bubbling sounds in the ink tanks.  I don't know if this is going to happen everytime i leave the printer alone for over a week but i'd like to avoid it.  Maybe leaving it on and letting it do those tiny auto head cleanings is the better way to go?  Opinions/advice?  

thanks!
Logged
madmanchan
Sr. Member
****
Offline Offline

Posts: 2110


« Reply #1 on: November 27, 2006, 06:13:46 AM »
ReplyReply

From what I recall of Michael's report, Canon recommends leaving the ipf5000 on all the time so that the printer can take care of itself will cleans as needed.  Of course, if it's doing a small clean every day, I don't know how that compares to doing a big clean every 12 days ...

Eric
Logged

michael
Administrator
Sr. Member
*****
Offline Offline

Posts: 4924



« Reply #2 on: November 27, 2006, 07:19:04 AM »
ReplyReply

Epson recommendds turning their printers off when not in use. Canon and HP say to leave them on.

This is due to the different head technology used.

Good advise in all cases.

Michael
Logged
John Hollenberg
Sr. Member
****
Offline Offline

Posts: 770


« Reply #3 on: November 27, 2006, 08:30:50 AM »
ReplyReply

Quote
Epson recommendds turning their printers off when not in use. Canon and HP say to leave them on.

This is due to the different head technology used.

Good advise in all cases.

Michael
[a href=\"index.php?act=findpost&pid=87341\"][{POST_SNAPBACK}][/a]

Michael,

Are you saying the printer will come out of sleep mode by itself to do a small cleaning when it isn't in use?

--John
Logged
madmanchan
Sr. Member
****
Offline Offline

Posts: 2110


« Reply #4 on: November 27, 2006, 09:01:22 AM »
ReplyReply

Quote
Michael,

Are you saying the printer will come out of sleep mode by itself to do a small cleaning when it isn't in use?

--John
[a href=\"index.php?act=findpost&pid=87348\"][{POST_SNAPBACK}][/a]

John, the following is quoted from Michael's ipf5000 early report (bold emphasis is mine):

Quote
Apparently the iPF 5000 knows when its heads needs cleaning, and does so itself. In fact, sometimes while it's just sitting there idling the printer spontaneously decides to run a cleaning cycle, seemingly for no apparent reason. But there is a reason, and it is based on a series of factors including total time on, time idle, time sleeping, time with heads capped, time spent printing, or not printing. Based on an equation that takes all of these timing factors into account, the printer may decide to run one of a number of different cleaning cycles. The most common of these apparently uses only a very tiny amount of ink. In the order of picoliters.

Eric
Logged

Gary Damaskos
Full Member
***
Offline Offline

Posts: 125


« Reply #5 on: November 27, 2006, 09:08:03 AM »
ReplyReply

When I leave mine on - that is what it does - all by itself!
Gary

Quote
Michael,

Are you saying the printer will come out of sleep mode by itself to do a small cleaning when it isn't in use?

--John
[a href=\"index.php?act=findpost&pid=87348\"][{POST_SNAPBACK}][/a]
Logged
John Hollenberg
Sr. Member
****
Offline Offline

Posts: 770


« Reply #6 on: November 27, 2006, 09:27:41 AM »
ReplyReply

Eric,

Yes, I saw that, but idling implies On, but not doing any printing (which is different than sleep mode).  So, I wanted to be sure.

--John
Logged
tbonanno
Full Member
***
Offline Offline

Posts: 100


WWW
« Reply #7 on: November 27, 2006, 10:27:28 AM »
ReplyReply

Hi John,

After reading this thread, I'll probaby leave mine on all the time.  Normally, I do leave it on.  However, during two extended trips (out of the country) more than two weeks each, I did turn it off.  After returning from the first trip, it went through what seemed like an extended cleaning cycle after powering on (probably like the one you described).  After returning from the second trip, I powered on and it did nothing out of the ordinary, no cleaning cycle or anything.  Just printed when I asked it to without any issues.  So I'm thiniking maybe it does have a mind of it own about these things  

Tony
Logged

Tony Bonanno Photography
ASMP General Member
Santa Fe, New Mexico
http://www.bonannophoto.com
TonyKarp
Newbie
*
Offline Offline

Posts: 12


« Reply #8 on: November 28, 2006, 09:20:37 AM »
ReplyReply

This is what I have done with my IPF5000:


1. Set the sleep timer to 60 min

Menu > System Setup > Sleep Timer > = 60 min.

This is more reasonable than the default, which is very short.


2. Leave the printer on.

The printer wakes up every once in a while to clean itself. Sort of like having a cat, but without the litter box. (Actually, the IPF5000 does have a litter box, but it doesn't have to be emptied that often.)


As a result, the printer has now made hundreds of prints without a single clog or printing failure, something I could never say about any of the Epsons I owned.
Logged
Dale Allyn
Full Member
***
Offline Offline

Posts: 225


WWW
« Reply #9 on: November 28, 2006, 10:27:36 AM »
ReplyReply

Quote
This is what I have done with my IPF5000:
1. Set the sleep timer to 60 min

Menu > System Setup > Sleep Timer > = 60 min.

This is more reasonable than the default, which is very short.
2. Leave the printer on.

The printer wakes up every once in a while to clean itself. Sort of like having a cat, but without the litter box. (Actually, the IPF5000 does have a litter box, but it doesn't have to be emptied that often.)
As a result, the printer has now made hundreds of prints without a single clog or printing failure, something I could never say about any of the Epsons I owned.
[a href=\"index.php?act=findpost&pid=87541\"][{POST_SNAPBACK}][/a]


Tony,

That's a good tip. Thanks.  I saw the menu item, but had yet to think to implement it.

Dale
Logged

michael
Administrator
Sr. Member
*****
Offline Offline

Posts: 4924



« Reply #10 on: November 28, 2006, 11:03:18 AM »
ReplyReply

Just one note on sleep mode, the iPF5000 won't go into sleep when it's set to Manual feed mode. Only when set to Cassette / Roll.

Michael
Logged
John Hollenberg
Sr. Member
****
Offline Offline

Posts: 770


« Reply #11 on: November 28, 2006, 12:30:02 PM »
ReplyReply

Quote
Just one note on sleep mode, the iPF5000 won't go into sleep when it's set to Manual feed mode. Only when set to Cassette / Roll.

Michael
[a href=\"index.php?act=findpost&pid=87557\"][{POST_SNAPBACK}][/a]

Odd.  Bug or design feature?  What would the reason be for this?

--John
Logged
michael
Administrator
Sr. Member
*****
Offline Offline

Posts: 4924



« Reply #12 on: November 28, 2006, 12:51:44 PM »
ReplyReply

Not sure. Next time I speak to the Canon tech rep I'll ask.

Michael
Logged
mr.dude
Jr. Member
**
Offline Offline

Posts: 57


« Reply #13 on: December 01, 2006, 03:12:08 AM »
ReplyReply

thanks for all the replies.  i'll be leaving it on
« Last Edit: December 01, 2006, 03:13:06 AM by mr.dude » Logged
Pages: [1]   Top of Page
Print
Jump to:  

Ad
Ad
Ad