Ad
Ad
Ad
Pages: [1]   Bottom of Page
Print
Author Topic: 2010 27" iMac - rookie question  (Read 2846 times)
Livingski
Newbie
*
Offline Offline

Posts: 3


« on: May 04, 2011, 11:25:23 PM »
ReplyReply

I am new to colour management and have spend the last few hours reading online, through various threads in this forum, and as you can expect, my head hurts.

So is my 2010 27" iMac a standard a standard or wide gamut display? Can this iMac be calibrated as I have read conflicting things?

Based on what I want to spend, it looks like a Spider 3, X-rite Eye-One Display 2, or try to find the X-rite DTP-94. The X-rite ColorMunki is pretty expensive in Canada and unfortunately some of the discounts apply to only the U.S.

I use labs to print my photos and a few lenses are higher on the need right now than another monitor and/or printer and although I wish I could get all, I can't.

Another topic that pops up is software: Chroma, Argyll CMS profiler, etc.

Any help would be greatly appreciated, what would be the top 2 choices for a 2010 iMac?

Thanks.

Logged
Czornyj
Sr. Member
****
Offline Offline

Posts: 1420



WWW
« Reply #1 on: May 05, 2011, 04:44:56 AM »
ReplyReply

iMac 27" is a normal gamut display, but it has pseudo-white LED backlight, that is as difficult to measure for common colorimeters as wide gamut displays. I'd buy the least expansive sensor, download ArgyllCMS + DispcalGUI, and borrow the spectro (CM or i1pro) to create correction matrix for the sensor+iMac spectra combination.
« Last Edit: May 05, 2011, 04:50:07 AM by Czornyj » Logged

Livingski
Newbie
*
Offline Offline

Posts: 3


« Reply #2 on: May 07, 2011, 01:15:35 PM »
ReplyReply

Thanks a lot for answering. I appreciate it.
Logged
Ethan_Hansen
Full Member
***
Offline Offline

Posts: 114


WWW
« Reply #3 on: May 07, 2011, 09:57:11 PM »
ReplyReply

If you have access to a i1Pro, you can perform the combined calibration mentioned above. If not, your best bet is the Spyder 3. Our recent evaluations of monitor measurement hardware - also discussed in this thread - shows the Spyder 3 as the colorimeter most capable with LED-lit screens.
Logged

Livingski
Newbie
*
Offline Offline

Posts: 3


« Reply #4 on: May 08, 2011, 12:50:04 AM »
ReplyReply

Thanks, one last question. I am nervous about the putting a suction cup on the monitor, is it better to use the counter weighted method or am I just being paranoid?

Thanks again.
Logged
Clearair
Full Member
***
Offline Offline

Posts: 131


« Reply #5 on: May 08, 2011, 04:36:27 AM »
ReplyReply

I always use counter weight method.
Angle the screen and clean.

Logged
na goodman
Sr. Member
****
Offline Offline

Posts: 350


« Reply #6 on: May 08, 2011, 07:02:43 AM »
ReplyReply

The suction cup was really for crt monitors.
Logged
KirbyKrieger
Sr. Member
****
Offline Offline

Posts: 418


WWW
« Reply #7 on: May 08, 2011, 12:21:25 PM »
ReplyReply

Someone with more experience may correct this, but my understanding is that your should NEVER use suction cups on an LCD screen.  I have two NEC monitors, and each goes out of its way to warn against the use of suction cups when profiling.
Logged

Ethan_Hansen
Full Member
***
Offline Offline

Posts: 114


WWW
« Reply #8 on: May 08, 2011, 01:18:26 PM »
ReplyReply

Someone with more experience may correct this, but my understanding is that your should NEVER use suction cups on an LCD screen.  I have two NEC monitors, and each goes out of its way to warn against the use of suction cups when profiling.
Yes! Unless you want to peel apart the layers of your monitor, keep suction cups away from LCD screens.
Logged

howardm
Sr. Member
****
Offline Offline

Posts: 757


« Reply #9 on: May 08, 2011, 02:49:02 PM »
ReplyReply

the exception being the 27" iMac which has a magnetically attached front glass piece over the actual LCD panel itself.
Logged
Wayne Fox
Sr. Member
****
Offline Offline

Posts: 2847



WWW
« Reply #10 on: May 08, 2011, 04:21:16 PM »
ReplyReply

the exception being the 27" iMac which has a magnetically attached front glass piece over the actual LCD panel itself.
In fact, to access an iMac most use a suction cup to pull the glass off the front.
Logged

Pages: [1]   Top of Page
Print
Jump to:  

Ad
Ad
Ad