Ad
Ad
Ad
Pages: [1]   Bottom of Page
Print
Author Topic: Gel / Light filter for Canon 580ex? What do you use?  (Read 5579 times)
haring
Full Member
***
Offline Offline

Posts: 198


WWW
« on: October 09, 2012, 06:40:08 PM »
ReplyReply

What kind of gels / filter kit do you use for your Canon 580EX? Canon provide a filter set up + gel for the latest flash but I have hard time finding filter kits for Canon 580EX flashes... There are some in the market (Rosco, etc.) but they seem to be poor quality...

What kind of gel do you use for your 580EX? Can you recommend a setup?

Thanks!
Logged

k bennett
Sr. Member
****
Offline Offline

Posts: 1433


WWW
« Reply #1 on: October 09, 2012, 06:48:21 PM »
ReplyReply

I buy the Rosco color correction filter pack. The sheets are 10x12 inches, and come in various strengths of CTO, CTB, magenta, and green. Costs about $30. I  just cut the filters to the right size and tape them over the front of my speedlight head with gaffer's tape. I get a lot of filters out of this pack. You can make precise filters by mixing, say, a Half CTO with a full plusgreen filter for some types of warm fluorescents.

There is always a Full CTO filter taped to the back of my flash for immediate use when needed.
Logged

Equipment: a camera and some lenses.
haring
Full Member
***
Offline Offline

Posts: 198


WWW
« Reply #2 on: October 09, 2012, 10:28:29 PM »
ReplyReply

I buy the Rosco color correction filter pack. The sheets are 10x12 inches, and come in various strengths of CTO, CTB, magenta, and green. Costs about $30. I  just cut the filters to the right size and tape them over the front of my speedlight head with gaffer's tape. I get a lot of filters out of this pack. You can make precise filters by mixing, say, a Half CTO with a full plusgreen filter for some types of warm fluorescents.

There is always a Full CTO filter taped to the back of my flash for immediate use when needed.

What happens if you want to change the color? Do you take the tape off?
Logged

k bennett
Sr. Member
****
Offline Offline

Posts: 1433


WWW
« Reply #3 on: October 10, 2012, 11:25:56 AM »
ReplyReply

The filters are taped on temporarily when needed. They swap out easily for different ones. Gaffer's tape is easy to remove and leaves no residue, and it can be reused many times.

Does that answer your question? I wasn't clear on what you were asking.
Logged

Equipment: a camera and some lenses.
Rhossydd
Sr. Member
****
Offline Offline

Posts: 1914


WWW
« Reply #4 on: October 10, 2012, 12:08:27 PM »
ReplyReply

I take the same rough and ready approach as Ken. Bits of CC gels taped over work fine, I just get off cuts from work, but you can buy samplers sets easily enough by mail order.
I use masking tape as some brands of gaffa tape can leave residues.
Logged
Ellis Vener
Sr. Member
****
Offline Offline

Posts: 1767



WWW
« Reply #5 on: October 10, 2012, 02:15:15 PM »
ReplyReply

I use the small gels in the Lee and Rosco sample books. They just fit over a 580 EX II lens. I use gaffer tape to attach them with. It isn't even toy rocket science.
Logged

Ellis Vener
http://www.ellisvener.com
Creating photographs for advertising, corporate and industrial clients since 1984.
Slobodan Blagojevic
Sr. Member
****
Online Online

Posts: 5735


When everybody thinks the same... nobody thinks.


WWW
« Reply #6 on: October 10, 2012, 02:23:44 PM »
ReplyReply

I use a $7.46 Rosco Strobist collection, a 55-peice kit, 1.5x3.25".

To attach it, I use a Scotch double-sided tape permanently attached to the flash (it is transparent). Before attaching a filter, I displace the protective cover (with the words Scotch on it, in the attachment below) just a bit (the sticky part is pretty strong). Cheap, simple, easy, pocketable.
Logged

Slobodan

Flickr
500px
Pages: [1]   Top of Page
Print
Jump to:  

Ad
Ad
Ad